sys: 0x200 try sd... bm:3 ERROR: sd: invalid bootinfo magic code:0x1000b8fa ERROR: invalid bootinfo image. ERROR: sd f! l:90 bm:4 nor m:0x20 d:0x4118 j... U-Boot SPL 2022.10ky (Jan 07 2025 - 13:44:01 +0800) [ 0.488] DDR type LPDDR4X [ 0.507] lpddr4_silicon_init consume 19ms [ 0.508] Change DDR data rate to 2400MT/s [ 0.724] Boot from fit configuration x1_orangepi-rv2 [ 0.726] ## Checking hash(es) for config conf_14 ... OK [ 0.731] ## Checking hash(es) for Image opensbi ... OK [ 0.736] ## Checking hash(es) for Image uboot ... OK [ 0.742] ## Checking hash(es) for Image fdt_14 ... OK [ 0.787] U-Boot 2022.10ky (Jan 07 2025 - 13:44:01 +0800) [ 0.790] CPU: rv64imafdcv [ 0.792] Model: ky x1 orangepi-rv2 board [ 0.796] DRAM: DDR size = 8192 MB [ 0.800] DDR size = 8192 MB [ 0.802] DDR size = 8192 MB [ 0.805] 8 GiB [ 0.880] reset driver probe start [ 0.882] reset driver probe finish [ 0.890] DCDC_REG1@dcdc1: enabling [ 0.892] DCDC_REG3@dcdc3: enabling [ 0.897] LDO_REG1@ldo1: enabling [ 0.901] SWITCH_REG1@switch1: enabling [ 0.902] SWITCH_REG2@pwr-event: enabling [ 0.906] SWITCH_REG3@pwr-int: enabling [ 0.909] SWITCH_REG4@rtc-ctrl: enabling [ 0.913] SWITCH_REG5@rtc-event: enabling [ 0.917] SWITCH_REG6@rtc-irq: enabling [ 0.921] SWITCH_REG7@power-down: enabling [ 0.924] SWITCH_REG8@reboot-flag: enabling [ 0.930] vcc3v3-pcie-regulator@vcc3v3_pcie: set 3300000 uV; enabling [ 0.935] DDR size = 8192 MB [ 0.940] Core: 416 devices, 30 uclasses, devicetree: board [ 0.953] WDT: Started PMIC_WDT with servicing (60s timeout) [ 0.958] WDT: Started watchdog@D4080000 with servicing (60s timeout) [ 0.967] MMC: sdh@d4280000: probe done. [ 0.973] sdh@d4281000: probe done. [ 0.974] sdh@d4280000: 0, sdh@d4281000: 2 [ 0.978] Loading Environment from SPIFlash... x1_qspi spi@d420c000: qspi iobase:0x0x00000000d420c000, ahb_addr:0x0x00000000b8000000, max_hz:26500000Hz [ 0.993] x1_qspi spi@d420c000: rx buf size:128, tx buf size:256, ahb buf size=512 [ 1.000] x1_qspi spi@d420c000: AHB read enabled [ 1.005] x1_qspi spi@d420c000: bus clock: 26500000Hz, PMUap reg[0xd4282860]:0x0000075b [ 1.013] x1_qspi spi@d420c000: AHB buf size: 512 [ 1.017] SF: Detected XM25QH128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK [ 1.039] Now init Rterm... [ 1.039] pcie prot id = 1, porta_init_done = 0 [ 1.043] Now waiting portA resister tuning done... [ 1.048] porta redonly_reg2: 00006d58 [ 1.051] pcie_rcal = 0x00006d58 [ 1.054] pcie port id = 1, lane num = 2 [ 1.058] Now int init_puphy... [ 1.061] waiting pll lock... [ 1.064] Now finish init_puphy.... [ 1.067] pcie_dw_x1 pcie@ca400000: Unable to get phy0 [ 1.072] pcie_dw_x1 pcie@ca400000: Unable to get phy1 [ 2.178] PCIE-0: Link down [ 2.183] sdh@d4281000: 74 clk wait timeout(100) [ 2.201] Card did not respond to voltage select! : -110 [ 2.203] mmc_init: -95, time 21 [ 2.222] Card did not respond to voltage select! : -110 [ 2.224] mmc_init: -95, time 18 [ 2.256] Found device 'hdmi@c0400500', disp_uc_priv=000000007deb4a70 [ 2.366] HDMI cannot get HPD signal [ 2.366] ky_display_init: device 'dpu@c0340000' display won't probe (ret=-1) [ 2.373] initialize_console_log_buffer [ 2.377] Have allocated memory for console log buffer [ 2.382] In: serial [ 2.384] Out: serial [ 2.386] Err: serial [ 2.390] Default to 100kHz [ 2.405] EEPROM: TlvInfo v1 len=38 [ 2.405] valid ethaddr: c0:74:2b:fa:72:48 [ 2.409] Cannot find TLV data: part# [ 2.413] Cannot find TLV data: serial# [ 2.416] Cannot find TLV data: manufacture_date [ 2.421] Cannot find TLV data: manufacturer [ 2.425] Cannot find TLV data: device_version [ 2.429] Cannot find TLV data: sdk_version [ 2.537] HDMI cannot get HPD signal [ 2.537] display devices not found or not probed yet: -1 [ 2.542] All buttons probed successfully [ 2.547] Read PMIC reg ab value f0 [ 2.550] Failed to get fastboot key config: -19 [ 2.555] sdh@d4280000: 74 clk wait timeout(100) [ 2.638] Card did not respond to voltage select! : -110 [ 2.640] mmc_init: -95, time 18 [ 2.643] can not get available blk dev [ 2.647] Net: RGMII interface [ 2.650] eth0: ethernet@cac80000 [ 2.655] Autoboot in 0 seconds [ 2.666] starting USB... [ 2.666] Bus ehci1@c0980100: ehci_x1_ci ehci1@c0980100: ehci_mv_probe Enter ... [ 2.676] mv_usb_phy usbphy1@c09c0000: x1-ci-usb-phy-probe: Enter... [ 2.681] ehci_x1_ci ehci1@c0980100: ehci-x1-ci: init hccr c0980100 and hcor c0980140 hc_length 64 [ 2.703] USB EHCI 1.00 [ 2.703] Bus dwc3@c0a00000: No USB maximum speed specified. Using super speed [ 2.716] mv_usb_phy usb2phy@0xc0a30000: x1-ci-usb-phy-probe: Enter... [ 2.720] x1_combphy phy@c0b10000: USB3 PHY init. [ 2.724] dwc3-generic-host dwc3@c0a00000: this is a DesignWare USB3 DRD Core [ 3.141] Register 2000140 NbrPorts 2 Starting the controller [ 3.144] USB XHCI 1.10 [ 3.146] scanning bus ehci1@c0980100 for devices... 1 USB Device(s) found [ 4.289] scanning bus dwc3@c0a00000 for devices... 3 USB Device(s) found [ 5.812] scanning usb for storage devices... 0 Storage Device(s) found [ 5.817] Device 0: unknown device [ 5.908] switch to partitions #0, OK [ 5.908] mmc0 is current device [ 5.919] Scanning mmc 0:3... [ 5.944] Found U-Boot script /boot.scr [ 5.955] 367 bytes read in 6 ms (59.6 KiB/s) [ 5.957] ## Executing script at 2c100000 [ 7.654] 27414016 bytes read in 1686 ms (15.5 MiB/s) [ 8.374] 11452721 bytes read in 714 ms (15.3 MiB/s) [ 8.395] 18627 bytes read in 14 ms (1.3 MiB/s) [ 8.396] Moving Image from 0x11000000 to 0x200000, end=1c8d000 [ 8.411] ## Loading init Ramdisk from Legacy Image at 21000000 ... [ 8.415] Image Name: Initial Ram Disk [ 8.419] Image Type: RISC-V Linux RAMDisk Image (gzip compressed) [ 8.425] Data Size: 11452657 Bytes = 10.9 MiB [ 8.430] Load Address: 00000000 [ 8.433] Entry Point: 00000000 Verifying Checksum ... OK [ 8.490] ## Flattened Device Tree blob at 31000000 [ 8.491] Booting using the fdt blob at 0x31000000 [ 8.597] Loading Ramdisk to 7d29c000, end 7dd880f1 ... OK [ 8.605] Loading Device Tree to 000000007d294000, end 000000007d29b8c2 ... OK Starting kernel ... [ 0.000000] Booting Linux on hartid 0 [ 0.000000] Linux version 6.18.0-rc1-yocto-standard-orangepi-rv2-00006-g9b332cece987 (oe-user@oe-host) (riscv64-poky-linux-gcc (GCC) 15.2.0, GNU ld (GNU Binutils) 2.45.0.20250908) #1 SMP Tue Oct 14 16:28:12 UTC 2025 [ 0.000000] Machine model: OrangePi RV2 [ 0.000000] SBI specification v1.0 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10003 [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] Malformed early option 'earlycon' [ 0.000000] efi: UEFI not found. [ 0.000000] OF: reserved mem: 0x000000007f000000..0x000000007fffffff (16384 KiB) map non-reusable framebuffer@7f000000 [ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable mmode_resv0@0 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000007ffff] [ 0.000000] node 0: [mem 0x0000000000080000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000100000000-0x000000027fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000027fffffff] [ 0.000000] SBI HSM extension detected [ 0.000000] riscv: base ISA extensions acdfimv [ 0.000000] riscv: ELF capabilities acdfimv [ 0.000000] Ticket spinlock: enabled [ 0.000000] percpu: Embedded 31 pages/cpu s86296 r8192 d32488 u126976 [ 0.000000] Kernel command line: console=ttyS0,115200 earlycon=sbi rw clk_ignore_unused rdinit=/bin/sh [ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] software IO TLB: area num 8. [ 0.000000] software IO TLB: mapped [mem 0x0000000079294000-0x000000007d294000] (64MB) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2097152 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] riscv: providing IPIs using SBI IPI extension [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000001] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000010] riscv-timer: Timer interrupt in S-mode is available via sstc extension [ 0.000296] Console: colour dummy device 80x25 [ 0.000364] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000375] pid_max: default: 32768 minimum: 301 [ 0.000484] LSM: initializing lsm=capability [ 0.000654] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000689] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.003117] riscv: ELF compat mode unsupported [ 0.003141] ASID allocator using 16 bits (65536 entries) [ 0.003339] rcu: Hierarchical SRCU implementation. [ 0.003344] rcu: Max phase no-delay instances is 1000. [ 0.003553] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.003678] EFI services will not be available. [ 0.004130] smp: Bringing up secondary CPUs ... [ 0.009367] smp: Brought up 1 node, 8 CPUs [ 0.010081] Memory: 8097632K/8388608K available (11983K kernel code, 5903K rwdata, 6144K rodata, 2436K init, 415K bss, 283976K reserved, 0K cma-reserved) [ 0.012928] devtmpfs: initialized [ 0.016365] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.016402] posixtimers hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.016489] futex hash table entries: 2048 (131072 bytes on 1 NUMA nodes, total 128 KiB, linear). [ 0.016755] pinctrl core: initialized pinctrl subsystem [ 0.017279] DMI not present or invalid. [ 0.017670] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.018087] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.018223] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.018257] audit: initializing netlink subsys (disabled) [ 0.018502] audit: type=2000 audit(0.000:1): state=initialized audit_enabled=0 res=1 [ 0.018790] thermal_sys: Registered thermal governor 'step_wise' [ 0.018863] cpuidle: using governor menu [ 0.040163] cpu4: Ratio of byte access time to unaligned word access is 2.45, unaligned accesses are fast [ 0.040162] cpu7: Ratio of byte access time to unaligned word access is 2.50, unaligned accesses are fast [ 0.040163] cpu3: Ratio of byte access time to unaligned word access is 2.58, unaligned accesses are fast [ 0.040163] cpu2: Ratio of byte access time to unaligned word access is 2.58, unaligned accesses are fast [ 0.040163] cpu1: Ratio of byte access time to unaligned word access is 2.55, unaligned accesses are fast [ 0.040163] cpu6: Ratio of byte access time to unaligned word access is 1.66, unaligned accesses are fast [ 0.040163] cpu5: Ratio of byte access time to unaligned word access is 1.64, unaligned accesses are fast [ 0.064201] cpu0: Ratio of byte access time to unaligned word access is 10.12, unaligned accesses are fast [ 0.069020] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.069030] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.069035] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.069038] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page [ 0.069761] ACPI: Interpreter disabled. [ 0.069911] iommu: Default domain type: Translated [ 0.069916] iommu: DMA domain TLB invalidation policy: strict mode [ 0.073024] SCSI subsystem initialized [ 0.073413] usbcore: registered new interface driver usbfs [ 0.073440] usbcore: registered new interface driver hub [ 0.073467] usbcore: registered new device driver usb [ 0.073964] Advanced Linux Sound Architecture Driver Initialized. [ 0.074772] vgaarb: loaded [ 0.075210] clocksource: Switched to clocksource riscv_clocksource [ 0.076020] pnp: PnP ACPI: disabled [ 0.082579] NET: Registered PF_INET protocol family [ 0.082872] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.089105] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.089170] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.089185] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.089538] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.092903] TCP: Hash tables configured (established 65536 bind 65536) [ 0.093066] UDP hash table entries: 4096 (order: 6, 262144 bytes, linear) [ 0.093263] UDP-Lite hash table entries: 4096 (order: 6, 262144 bytes, linear) [ 0.093662] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.094368] RPC: Registered named UNIX socket transport module. [ 0.094377] RPC: Registered udp transport module. [ 0.094380] RPC: Registered tcp transport module. [ 0.094382] RPC: Registered tcp-with-tls transport module. [ 0.094385] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.094402] PCI: CLS 0 bytes, default 64 [ 0.094829] Unpacking initramfs... [ 0.095712] workingset: timestamp_bits=46 max_order=21 bucket_order=0 [ 0.096531] NFS: Registering the id_resolver key type [ 0.096560] Key type id_resolver registered [ 0.096565] Key type id_legacy registered [ 0.096589] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.096594] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.096872] 9p: Installing v9fs 9p2000 file system support [ 0.097144] NET: Registered PF_ALG protocol family [ 0.097206] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.097408] io scheduler mq-deadline registered [ 0.097417] io scheduler kyber registered [ 0.097452] io scheduler bfq registered [ 0.102316] riscv-plic: interrupt-controller@e0000000: mapped 159 interrupts with 8 handlers for 16 contexts. [ 0.147793] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.160306] loop: module loaded [ 0.162115] e1000e: Intel(R) PRO/1000 Network Driver [ 0.162126] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 0.162797] usbcore: registered new interface driver uas [ 0.162840] usbcore: registered new interface driver usb-storage [ 0.163065] mousedev: PS/2 mouse device common for all mice [ 0.163698] sdhci: Secure Digital Host Controller Interface driver [ 0.163706] sdhci: Copyright(c) Pierre Ossman [ 0.163726] Synopsys Designware Multimedia Card Interface Driver [ 0.163850] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.164402] usbcore: registered new interface driver usbhid [ 0.164406] usbhid: USB HID core driver [ 0.164708] riscv-pmu-sbi: SBI PMU extension is available [ 0.164744] riscv-pmu-sbi: 16 firmware and 18 hardware counters [ 0.166968] NET: Registered PF_INET6 protocol family [ 0.168150] Segment Routing with IPv6 [ 0.168201] In-situ OAM (IOAM) with IPv6 [ 0.168253] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 0.168777] NET: Registered PF_PACKET protocol family [ 0.168856] 9pnet: Installing 9P2000 support [ 0.168938] Key type dns_resolver registered [ 0.193804] printk: legacy console [ttyS0] disabled [ 0.194164] d4017000.serial: ttyS0 at MMIO 0xd4017000 (irq = 14, base_baud = 921600) is a XScale [ 0.194205] printk: legacy console [ttyS0] enabled [ 0.511510] Freeing initrd memory: 11184K [ 0.718037] clk: Not disabling unused clocks [ 1.144451] PM: genpd: Disabling unused power domains [ 1.149491] ALSA device list: [ 1.1524[ 1.157258] Freeing unused kernel image (initmem) memory: 2436K [ 1.160667] Run /bin/sh as init process /bin/sh: can't access tty; job control turned off ~ # uname -a Linux (none) 6.18.0-rc1-yocto-standard-orangepi-rv2-00006-g9b332cece987 #1 SMP Tue Oct 14 16:28:12 UTC 2025 riscv64 GNU/Linux